The Amazing Red Planet Red Rover Robotics Come On Over Rover Get Me Off This Planet

This lesson discusses how each component of a spacecraft is specifically designed so that a rover can land safely in six minutes. Also, students will learn how common, everyday materials and technology, like nylon, polyester and airbags, are used in space-age technology.

Engineers are experts at designing equipment and technologies for safety and protection. To endure the massive forces of entry and landing on Mars, engineers designed an aeroshell, parachute, rock thrusters, lander and airbag system. In our everyday lives, we see the benefits gained from smart engineering design: vehicle air bags, advanced braking systems, traffic lights, circuit breakers, GFI electrical outlets, factory air filters, motorcycle helmets, etc. Mars rover entry descent landing After this lesson, students should be able to: Describe the engineering process and steps of landing the rover safely. Identify several components of a Mars lander designed by engineers. Recognize that at extremely high speeds, atmospheric friction causes intense heating. Identify the different materials used for the parachute. How long does it take for a 12,000 mph speeding spacecraft to come to a stop? How about a spacecraft that is exceeding 16 times the speed of sound or 20 times faster than a speeding bullet? Or, a spacecraft that is housing a multi-million dollar Mars rover that has been traveling through space for about 6 months? Well, NASA engineers know precisely what it takes to slow down and finally stop these spacecraft. Believe it or not, it takes only six minutes to bring a spacecraft to a full stop! Engineers use a combination of an aeroshell, parachute, rocket thrusters and airbags to safely slow down and land the spacecraft, rover and lander. When a spacecraft is traveling this fast, the friction of the atmosphere causes extreme heat on the spacecraft. The aeroshell, parachute and rocket thrusters prevent the spacecraft from burning up in the Martian atmosphere and crashing into the surface, while the airbags allow the lander to safely "bounce" its way to a stop in order to deploy the rover. A rover is carried through space in a spacecraft (which is separate from the actual launch vehicle, which is a rocket that propels a spacecraft into space). The spacecraft is designed to safely carry and maneuver the rover as it enters the Martian atmosphere and lands on Mars. Two major units of spacecrafts are the cruise stage and the entry, descent, and landing system (which includes the aeroshell). In short, a launch vehicle projects a spacecraft into space, where it spends up to 6 months traveling, or cruising, the millions of miles between Earth and Mars. Forty-five days before entry into the Martian atmosphere, the cruise phase of traveling through space comes to an end, and several preparation steps are carried out to end this phase and begin the entry, descent and landing phase — also called "six minutes of terror" by NASA engineers. First, the spacecraft switches from medium-gain to low-gain antenna communication allowing engineers to more accurately track the spacecraft and support its safe delivery to the surface of Mars. Next, the spacecraft rotates so that its heat shield — which protects the rover from intense heat — faces forward. Finally, cruise stage separation begins, shedding over half of the spacecraft's weight, and the six minutes of terror commences. The part of the spacecraft that remains after the cruise stage separates is called the entry, descent, and landing system and includes the aeroshell (see Figure 2), which is made up of two parts; a heat shield and a backshell. The heat shield is the flat-brownish half of the aeroshell, which serves two functions. First, as the name implies, it shields the spacecraft from heat caused by atmospheric friction. At 12,000 mph, the temperature of the heat shield will reach 1,447 °C (2,637 °F), which is as hot as the surface of the sun! Clearly, protection is needed. Second, since the shield's surface is flat and not very aerodynamic, it acts to slow the spacecraft down to about 1000 mph in four minutes. The white half of the aeroshell is termed the backshell, which holds the parachute, rockets, lander and rover. Once the aeroshell's heat shield has slowed down the spacecraft, and it is about 30,000 ft above the Martian surface, a parachute is ejected from the backshell (see Figure 3). The parachute is made from two common fabrics: polyester and nylon. Polyester is used for a number of reasons: extremely strong, resists creasing, withstands moisture, and is able to resist acid; and nylon is used for a variety of reasons, also: absorbs energy, highly elastic and extensible, and resists tearing under shock loads. The parachute's bridle (the tethers that hold it to the backshell) are made of Kevlar, the same material used to manufacture bulletproof vests. Once the parachute is deployed, about 6 miles above the surface, the heat shield is detached and the lander disconnects from the backshell; while the lander is technically detached, it is actually still connected to the backshell by a 65 foot (20 meter) bridle, made of braided Zylon — an advanced fiber material similar to Kevlar that is sewn specifically in a webbing pattern (like shoelace material) to make it stronger. Once the lander/backshell separation occurs, airbags — made of synthetic Vectran, which has almost twice the strength of other synthetic materials, such as Kevlar, and performs better at cold temperatures — inflate to prepare for landing (Figure 4). Because the Martian atmosphere is very thin, the deployed parachute is not enough to slow the spacecraft's backshell; rockets are used to bring the spacecraft to a vertical stop, about 30-50 feet above the surface. Fun Fact: Students should be familiar with the concept of the parachute but they may not know that the idea of a parachute dates back to Leonardo DaVinci (1452-1519). However, Louis Sebastien Lenormand is often credited for the invention of the first practical parachute in 1783. (http://inventors.about.com/library/inventors/blparachute.htm) At this point, the spacecraft has slowed down from 12,000 mph to a vertical stop about four or five stories above the surface. However, arguably the most exciting and dangerous part of the landing is not over yet. The bridle is now cut and the 1,200 pound (544 kg) lander and rover will freefall to the Mars surface, marking the end of six minutes of nail biting terror for engineers. The lander could bounce up to 10 minutes and make 30-40 bounces over a kilometer (more than half a mile) of the Martian surface before it finally comes to a stop and the airbags deflate. Finally, the pedals of the lander open up to expose the rover, which then deploys its solar array and raises its panoramic camera. Communication begins between the rover and the Mars Odyssey orbiter satellite, and the rover is ready to roam the Martian surface. The configuration of the spacecraft for travel between Earth and Mars. The remaining spacecraft after its separation with the cruise stage. It is made up of two parts: a heat shield and a backshell. The brownish half of the aeroshell made to withstand temperatures as hot as the surface of the sun (1,447 °C or 2,637 °F). The white half of the aeroshell which houses the parachute, airbags, rockets, lander, and rover. Rope or chord-like tethers used to connect both the parachute and lander to the backshell. Shell with airbags which protects the rover while bouncing along the Mars surface. An unmanned vehicle sent to explore an unknown area. Egg-cellent Landing From other lessons in the Mission to Mars unit, we learned why scientists are so interested in studying Mars, how scientists and engineers design and manufacture a rover to gather scientific information, and how it is possible to transport the rover from Earth to Mars. This lesson described the steps and design for accomplishing one of the most difficult tasks of the mission: landing the rover safely on Mars. Aerospace engineers had to design how the aeroshell, parachutes, and rockets would safely slow down the spacecraft while entering the Martian atmosphere. Materials engineers had to select advanced materials such as the nylon and polyester for the parachutes and Vectran for the airbags, while mechanical engineers had to design the structure of the lander and airbags for a cushioned landing and safe stop. Finally, electrical engineers and computer science engineers had to integrate all of the circuitry together for navigation and communication of the spacecraft. A great team of engineers created a state-of-the-art piece of equipment, the rover, which allows scientists to study the Red Planet remotely. Discussion Question: Solicit, integrate and summarize student responses. Ask the students what problems they might face when trying to land a 12,000 mph speeding spacecraft on another planet like Mars. (Possible answers: burning up in the atmosphere, slowing down the spacecraft, not crashing into the surface, or finding a safe place to land — i.e., not landing in an ocean if the planet had water.) Poll: Before the lesson, ask all students the same question. Have students raise their hand to answer the question. Write answers (or key facts) on the board, and summarize (in percentages or actual number of students) who answered the same or similarly. Ask students: How long do they think it takes for NASA engineers to slow down and finally stop a 12,000 mph speeding spacecraft to 0 mph? (Answer: 6 minutes) Deceleration Calculation: Calculate an equation, and summarize student responses. Write the correct answer on the board. The deceleration of a stopping object can be calculated by dividing the velocity (or speed) of the object by how long it takes to stop. With velocity in mph and time in seconds, what is the deceleration of the spacecraft to stop? (Answer: 33.33 mph/sec.) This means on average the spacecraft slows down 33 mph every second, which is almost twice as hard as someone slamming on their brakes in a car. Human Matching: On 14 pieces of paper, write either the term or the definition of the seven vocabulary words. Ask for 14 volunteers from the class to come up to the front of the room, and give each person one of the pieces of paper. One at a time, have each volunteer read what is written on his/her paper. Have the remainder of the class match term to definition by voting. Have student "terms" stand by their "definitions." At the end, give a brief explanation of the concepts. Question/Answer: Have students answer the following questions in a short paragraph in journals or on a sheet of paper: What three components help slow the spacecraft during entry into the Martian atmosphere? (Answers: The aeroshell's heat shield, because of its non-aerodynamic shape, a parachute, and rockets.) What common clothing materials are used in making the parachute? (Answer: polyester and nylon) After the lander is cut from the backshell and free falls to the surface of Mars, it bounces to a stop. About how many bounces are necessary before the lander fully stops? (Answer: 30 - 40 bounces) Entry, Descent, and Landing Video - Have students visit NASA's website and watch their Entry, Descent, and Landing video with engineering commentary on the design and challenges of landing the rover. http://marsrovers.jpl.nasa.gov/gallery/video/challenges.html (or click on a direct link to the video http://marsrovers.jpl.nasa.gov/gallery/video/movies/mer_ch_edl_TerrorComb.mpg or http://marsrovers.jpl.nasa.gov/gallery/video/movies/mer_ch_edl_TerrorComb.mov ) http://marsrovers.jpl.nasa.gov/home/index.html http://inventors.about.com/library/inventors/blparachute.htm http://inventors.about.com/gi/dynamic/offsite.htm?site=http://whyfiles.news.wisc.edu/032air%5Fbag/mars%5Flander.html http://inventors.about.com/library/inventors/blair_bags.htm http://www.jcfa.gr.jp/english/5-technologies.html http://www.kubicekballoons.cz/english/products/index.php?u=fabrics.php